Autopilot · Flight Controller

N7 Autopilot Flight Controller

ArduPilot / PX4 autopilot with STM32H7, redundant dual IMUs and built-in shock absorption

N7 Autopilot Flight Controller

Overview

N7 is an ArduPilot / PX4 autopilot built on an STM32H7 processor at 480 MHz with an STM32F103 co-processor. It has dual-redundant IMUs, an internal shock-absorbing structure and IMU heating for low temperatures. With 4 UART ports, 1 CAN port and 8 standard PWM plus 5 programmable IO, it serves planes, multirotors, helicopters, VTOLs, UGVs and USVs. It measures 47 x 68 x 19 mm and weighs 57 g.

  • STM32H7 processor, 480 MHz
  • Dual IMU, internal shock absorption
  • 47 x 68 x 19 mm, 57 g
N7 — Autopilot

Key features

  • STM32H7 processor with a co-processor

    The STM32H743IIK6 (Arm Cortex-M7, 480 MHz, 2 MB flash, 1 MB RAM) has a double-precision floating-point unit. An STM32F103 (Cortex-M3, 72 MHz) serves as co-processor.

  • Dual IMU and dual magnetometer redundancy

    BMI088 and ICM20689 IMUs back each other up. Magnetometer redundancy pairs the onboard IST8310 compass with the compass in the GPS module. The barometer is an MS5611.

  • 4 UART, 3 I2C, 1 CAN, 8 PWM plus 5 programmable IO

    Eight standard PWM IO and five programmable IO sit alongside SBUS / PPM RC input, a power module input, a GPS & safety port, USB Type-C and a TF card slot.

  • Internal shock absorption and IMU heating

    An internal shock-absorbing structure suits a range of airframes, and built-in heating resistors keep the IMU at a constant temperature in low-temperature environments.

  • ArduPilot and PX4 with open-source tools

    Runs PX4 or ArduPilot firmware on planes, multirotors, helicopters, VTOLs, UGVs and USVs, and is used with QGroundControl and Mission Planner.

  • 47 x 68 x 19 mm, 57 g

    Operates from -20 ℃ to 65 ℃ on a 4.5–5.5 V power module input, with a servo voltage input of 0–10 V. A flight controller power module is included in the package.

Technical specifications

Hardware2
N7 — Hardware
Main ProcessorSTM32H743IIK6
(32 Bit Arm® Cortex®-M7, 480 MHz, 2 MB memory, 1 MB RAM)
Co-processorSTM32F103
(32 Bit Arm® Cortex®-M3, 72 MHz, 20 KB SRAM)
Sensors3
N7 — Sensors
Accelerometer / GyroBMI088 / ICM20689
Electronic CompassIST8310
BarometerMS5611
External Interface9
N7 — External Interface
UART Serial Port4
I2C3
CAN1
PWM Output8 x Standard PWM IO
5 x Programmable IO
RC InputSBUS, PPM
Power Module Input1
GPS & Safety1
USB (Type-C)1
TF Card Slot1
Overall7
N7 — Overall
Compatible ModelPX4 / ArduPilot Firmware
(Planes / Multirotors / Helicopters / VTOL / UGV / USV)
Power Module Voltage Input4.5 ~ 5.5 V
USB Voltage Input5 V (±0.25 V)
Servo Voltage Input0 ~ 10 V
Working Temperature-20 ℃ ~ 65 ℃
Dimensions47 x 68 x 19 mm
Weight57 g
In the box

N7 Autopilot

  • N7 Autopilot Packaging Box x1
  • N7 Autopilot x1
  • Flight Controller Power Module x1
  • I2C Adapter Cable / CAN Adapter Cable x2
  • TELEM4 to I2C Cable x1
  • SBUS Signal Adapter Cable x1
  • TELEM1 Adapter Cable x1
  • N7 Gimbal Interface Cable x1
  • Type-C USB Data Cable x1
  • 3M Double-sided Adhesive x3

Item names as listed by SIYI. Contents can vary by combo.

Specifications are taken from the SIYI website as of 1 October 2026 and may be revised by the manufacturer without notice. View this product on the SIYI website

Where it is used

Based on the reference configurations and case studies SIYI has published that use this product.

Recommended solutions

SIYI reference configurations that include this product.

Frequently asked questions about N7

What supply voltage does the N7 flight controller need?

The flight controller is supplied with 4.5–5.5 V.

Do the flight controller's pins provide an output voltage?

No. The pins carry no output voltage; power has to come from an external supply.

Which firmware does the N7 run?

N7 runs open-source firmware and supports both ArduPilot and PX4. Using it requires knowledge of open-source flight controller setup and tuning.

Which external interfaces are available on the N7?

It has 4 UART serial ports, 3 I2C, 1 CAN, 8 standard PWM IO plus 5 programmable IO, RC input (SBUS, PPM), 1 power module input, 1 GPS and safety switch port, 1 USB Type-C port and 1 TF card slot.

Can the flight controller read motor speed in real time?

This requires a propulsion system that supports the CAN protocol.

What should be done if the aircraft vibrates too much?

Add an external vibration damping plate to the installation.

Articles and case studies featuring N7

UniFC 6 PICO Compact Flight ControllerNew

Autopilot

UniFC 6 PICO

Compact ArduPilot / PX4 autopilot with STM32H7, dual IMU and barometer, 100 Mbps Ethernet

  • STM32H7 processor, 480 MHz
  • Dual IMU + dual barometer
  • 49 x 42.6 x 16.2 mm, about 40 g
F9P RTK Multi-Frequency GNSS Positioning Module

Autopilot

F9P RTK

ZED-F9P RTK module usable as mobile station or base station, with dual-module heading

  • Positioning accuracy 1 cm + 1 ppm
  • u-blox ZED-F9P, 184 channels
  • Mobile or base station use
UniGNSS M10 DroneCAN GNSS ModuleNew

Autopilot

UniGNSS M10

u-blox M10 GNSS module on DroneCAN with compass, status light, buzzer and safety switch

  • DroneCAN, u-blox M10 receiver
  • Horizontal accuracy 1.5 m CEP
  • 4 GNSS received concurrently

Interested in N7?

Send us your requirements for more information, a quotation or advice on choosing a configuration.

Search the site

e.g. ZT30, thermal camera, inspection drone, RTK