Autopilot · Power Module

N7 Flight Controller Power Module

2–14S power module with 5.2 V output and battery voltage and current monitoring

N7 Flight Controller Power Module

Overview

This power module supplies the N7 flight controller from a 2S to 14S battery, stepping the voltage down to a stable 5.2 V at 2 A continuous and 3 A maximum. It detects battery voltage and current, from which remaining battery power and remaining flight time are estimated. The mainboard carries 60 A constant current and 100 A peak current for under 60 s, and the BEC includes reverse protection.

  • 2–14S input, 5.2 V output
  • 60 A constant, 100 A peak (<60 s)
  • Current measurement up to 120 A
N7 Flight Controller Power Module — Autopilot

Key features

  • Battery voltage and current detection

    The module detects battery voltage and current so that remaining battery power can be calculated and remaining flight time estimated.

  • 2S to 14S input, stable 5.2 V output

    A step-down converter and BEC feed the flight controller mainboard with 5.2 V at 2 A continuous and 3 A maximum.

  • 60 A constant and 100 A peak current

    The mainboard carries 60 A constant current and 100 A peak current for less than 60 s. Maximum measuring current is 120 A, with a voltage divider ratio of 18.18 and 36.36 A/V.

  • BEC reverse protection

    Reverse protection on the BEC adds a layer of safety redundancy for the equipment.

  • 23 × 29 mm mainboard, XT60 battery connector

    The mainboard measures 23 × 29 mm and the module weighs 32 g including the connection cable and connector. The battery connector is an XT60.

Technical specifications

Overall10
N7 Flight Controller Power Module — Overall
Voltage Input2 ~ 14 S
Voltage Output5.2V
Current OutputContinuous current: 2A
Maximum current: 3A
Voltage Divider Ratio18.18
A / V36.36
Mainboard Constant Current60A
Mainboard Peak Current100A ( <60s )
Max Measuring Current120A
Dimensions23 × 29 mm
Weight32g (including connection cable and connector)

Specifications are taken from the SIYI website as of 1 October 2026 and may be revised by the manufacturer without notice. View this product on the SIYI website

Frequently asked questions about N7 Flight Controller Power Module

What input voltage range does the power module support?

It accepts battery input from 2S to 14S.

What does the module supply to the flight controller?

It outputs 5.2 V, with 2 A continuous current and 3 A maximum current.

What type of battery connector does it use?

The battery connector is an XT60.

How much current can the mainboard carry?

The mainboard constant current is 60 A and the peak current is 100 A for less than 60 seconds.

What is the maximum current the module can monitor?

The current monitoring range goes up to 120 A.

How is the sensor calibrated?

Power the system from a battery, connect to the ground station and measure the battery voltage with a multimeter or battery checker. Then set the sensor version to 0 in the ground station software and type in the measured voltage; it calculates the voltage divider coefficient and saves it to the flight controller. The current reading needs no further calibration.

Articles and case studies featuring N7 Flight Controller Power Module

N7 Autopilot Flight Controller

Autopilot

N7

ArduPilot / PX4 autopilot with STM32H7, redundant dual IMUs and built-in shock absorption

  • STM32H7 processor, 480 MHz
  • Dual IMU, internal shock absorption
  • 47 x 68 x 19 mm, 57 g
UniFC 6 PICO Compact Flight ControllerNew

Autopilot

UniFC 6 PICO

Compact ArduPilot / PX4 autopilot with STM32H7, dual IMU and barometer, 100 Mbps Ethernet

  • STM32H7 processor, 480 MHz
  • Dual IMU + dual barometer
  • 49 x 42.6 x 16.2 mm, about 40 g

Interested in N7 Flight Controller Power Module?

Send us your requirements for more information, a quotation or advice on choosing a configuration.

Search the site

e.g. ZT30, thermal camera, inspection drone, RTK