
UAV Flight Controller Guide: Choosing an Autopilot, GNSS and RTK
What to compare when choosing a UAV flight controller: processor, sensor redundancy, interfaces and vehicle support, plus SIYI GNSS and RTK positioning modules.
Autopilot · Flight Controller
Compact ArduPilot / PX4 autopilot with STM32H7, dual IMU and barometer, 100 Mbps Ethernet

UniFC 6 PICO is a compact autopilot measuring 49 x 42.6 x 16.2 mm and weighing about 40 g. It runs ArduPilot or PX4 on an STM32H7 processor at 480 MHz, with dual IMUs, dual barometers and IMU heating. Five UART ports, two CAN ports, 14 PWM outputs and a 100 Mbps Ethernet port link it to peripherals and onboard computers on multirotors, fixed-wing aircraft, VTOLs, helicopters, UGVs and USVs.

The STM32H743IIK6 (32-bit Arm Cortex-M7) runs at 480 MHz with 2 MB of flash and 1 MB of RAM, leaving headroom for further development.
ICM45686 and BMI088 IMUs and two ICP20100 barometers back each other up if one sensor fails temporarily. IMU heating holds a constant temperature to reduce drift in the cold.
Also provides SBUS / PPM RC input, a power module input, a GPS & safety port, USB Type-C, a TF card slot and Ethernet. The PWM output level switches between 3.3 V and 5 V.
The Ethernet port connects an onboard computer for functions such as swarming, AI tracking and recognition, and mapping.
Runs PX4 or ArduPilot firmware on UGVs, USVs, fixed-wing aircraft, 3–8 axis multirotors, helicopters and VTOLs. Parameter tuning and control are handled in SIYI UniGCS.
The small body leaves more wiring space on FPV and other compact platforms. It operates from -30 to 60 ℃ on a 4.5–5.5 V power module input, with a servo voltage input of 0–9.5 V.
| Main Processor | STM32H743IIK6 (32 Bit Arm ® Cortex®-M7, 480MHz, 2MB memory, 1MB RAM) |
|---|
| Accelerometer / Gyro | ICM45686 / BMI088 |
|---|---|
| Electronic Compass | IST8310 |
| Barometer | ICP20100 x2 |
| UART Serial Port | 5 |
|---|---|
| I2C | 3 |
| CAN | 2 |
| PWM Output | 14 |
| RC Input | SBUS, PPM |
| Power Module Input | 1 |
| GPS & Safety | 1 |
| USB (Type-C) | 1 |
| TF Card Slot | 1 |
| Compatible Model | PX4 / ArduPilot Firmware (Ugvs, usvs, fixed-wing, 3–8 axis multi-rotor, helicopter, VTOL, etc.) |
|---|---|
| Power Module Voltage Input | 4.5 ~ 5.5 V |
| USB Voltage Input | 5 V (±0.25 V) |
| Servo Voltage Input | 0 ~ 9.5 V |
| Working Temperature | -30 ~ 60 ℃ |
| Dimensions | 49 x 42.6 x 16.2 mm |
| Weight | About 40 g |
Dimensions (With Package): L182 * W123 * H26 mm · Weight (With Package): 175 g
Item names as listed by SIYI. Contents can vary by combo.
Specifications are taken from the SIYI website as of 18 November 2026 and may be revised by the manufacturer without notice. View this product on the SIYI website
SIYI has not published a reference configuration that names this model. Products in the Autopilot line are used in solutions for these platforms.

What to compare when choosing a UAV flight controller: processor, sensor redundancy, interfaces and vehicle support, plus SIYI GNSS and RTK positioning modules.

Autopilot
ArduPilot / PX4 autopilot with STM32H7, redundant dual IMUs and built-in shock absorption

Autopilot
Single-module, dual-antenna multi-frequency RTK receiver with a PNI RM3100 compass

Autopilot
ZED-F9P RTK module usable as mobile station or base station, with dual-module heading

Autopilot
u-blox M10 GNSS module on DroneCAN with compass, status light, buzzer and safety switch
Send us your requirements for more information, a quotation or advice on choosing a configuration.